manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 200

17 Parallel tests

200

ARGUS 152

Display during HTTP download:

Display of test status:

-

Current download/total number of 
downloads, in this example the first 
download attempt out of three (1/3) is 
displayed.

-

Data transferred so far (in this example 
6 %)

-

Current net average download rate (in 
this example 72,106 Mbit/s)

See page 127 for further result parameters.

Cancels test

-

Currently selected test as well as test-
dependent result parameters, in this 
example the current net average 
download rate, the current progress and 
the size of the file to be transferred.

The display of results depends on the 
respective test. See the chapter on the 
individual test for more information on 
the result parameters.

-

The current download in kbit/s is 
represented as a percentage of the 
entire downstream range.

-

The current upload in kbit/s is 
represented as a percentage of the 
entire upstream range.

-

Number of CRC and FEC errors in down- 
and upstream

 

or

Switches to the test result 
parameters, in this example for HTTP 
download.

<Stop>

Stops the test, in this example 
HTTP download.

HTTP download

Cursor down

Test status

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands