manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 172

16 IPTV tests

172

ARGUS 152

Display:

Display (MDI according to  RFC 4445):

Display:

-

Current bitrate

-

Number of packets lost during the test

-

Display of packet loss rate in percent

<Detail>

Switches to the IPTV details.

-

Displays the current delay factor in ms

-

Displays the minimum delay factor in ms

-

Displays the maximum delay factor in ms

-

Displays the average delay factor in ms

-

Displays the media loss rate (MLR) in 
percent

-

Duration of test

-

Displays the name of the selected 
broadcaster

-

Display of broadcaster's IP address

-

Display of broadcaster's port

-

Display of IGMP latency (switch-on time 
of program) in ms

<RTP/UDP>

Switches to RTP/UDP details, 
see page 173.

Continued on 
next page

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands