manualshive.com logo in svg

Argus 152, Manual

The Kenmore 152 is a versatile and reliable appliance that simplifies your daily chores. To gain full control and maximize its potential, make sure to download the comprehensive Owner's Manual from manualshive.com for free. This handy manual is your go-to resource, offering detailed instructions and tips for optimal product usage.

Share
Download
background image

15 VoIP tests

150

ARGUS 152

STUN server

Use

STUN

Use STUN: select yes or no

If a NAT router is located between ARGUS and the 
nearest remote station (gateway), STUN must be used 
so that ARGUS can determine under which IP address 
the remote station sees ARGUS. Default: 

no

STUN server

STUN server: address of a STUN server, which must be 
in the same network (on the same level) as the remote 
station.

Rated/tre-
shold value

MOS rates value Entry of MOS setting:

The mean opinion score (MOS) assesses the quality of 
voice data. The MOS quality scale ranges from 5 
(excellent) to 1 (bad). On the basis of the set MOS 
value, ARGUS rates the current VoIP voice link as "OK" 
(current MOS value achieves MOS setting) or "FAIL".

Range: 1.0 to 5.0

Default: 

4.0

The MOS value here is stated as MOS

CQE

 

(conversational quality estimated). The use of a specific 
codec has a significant influence on this.

Jitter treshold

Determines the treshold for the jitter.

Range: 0 to 200 ms

Default: 

* (off)

RTP loss 

treshold

Determines the treshold for the RTP loss treshold.

Range: 0 to 100 %

Default: 

* (off)

Profile 
name

Enter/modify name of edited VoIP profile.

value

5

4

3

2

1

Voice quality excellent

good

fair

poor

bad

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
D-Link DSL-2640BT Installation Manual preview
DSL-2640BT
Brand: D-Link Pages: 12
8e6 Technologies Enterprise Filter Authentication R3000 Quick Start Manual preview
Enterprise Filter Authentication R3000
Brand: 8e6 Technologies Pages: 66
SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Brand: SAF Pages: 30
REXROTH efc series Instruction Manual preview
efc series
Brand: REXROTH Pages: 68
Aztech DSL1000EW(L) Speci?Cations preview
DSL1000EW(L)
Brand: Aztech Pages: 2
VCS VideoJet 100 Manual preview
VideoJet 100
Brand: VCS Pages: 118
Kontron 50099 067 User Manual preview
50099 067
Brand: Kontron Pages: 42
Maipu SM3100-9TC-AC Install Manual preview
SM3100-9TC-AC
Brand: Maipu Pages: 26
Zhone 6388-A1-XXX Technical Specifications preview
6388-A1-XXX
Brand: Zhone Pages: 2
National Instruments NI 9229E Operating Instructions Manual preview
NI 9229E
Brand: National Instruments Pages: 26
Hanwha Techwin Wisenet XRN-6410DB4 User Manual preview
Wisenet XRN-6410DB4
Brand: Hanwha Techwin Pages: 118
Alcatel OmniSwitch 6624 Network Configuration Manual preview
OmniSwitch 6624
Brand: Alcatel Pages: 546
IBM 32R1860 - Nortel Layer 2/3 Copper GbE Switch... User Manual preview
32R1860 - Nortel Layer 2/3 Copper GbE Switch...
Brand: IBM Pages: 14
National Instruments GPIB-120A User Manual preview
GPIB-120A
Brand: National Instruments Pages: 36
WAVESYS WSIL-1204-GT2-SFP2 Hardware User Manual preview
WSIL-1204-GT2-SFP2
Brand: WAVESYS Pages: 21
Billion BiPAC 7404VGO Specifications preview
BiPAC 7404VGO
Brand: Billion Pages: 2
Riverbed SteelCentral AppResponse 2170 Installation Manual preview
SteelCentral AppResponse 2170
Brand: Riverbed Pages: 166

Brands by name

Popular brands

Load more brands