manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 108

13 ATM tests

108

ARGUS 152

13 ATM tests 

The following ATM tests can only be performed on an ADSL interface. Other interfaces 
such as VDSL or Ethernet are not based on ATM.

13.1 VPI/VCI scan

In VPI/VCI scan, ARGUS checks which VPI/VCI combinations are active on the test 
access. ARGUS transmits a test packet for all possible VPI/VCI and waits for a response 
packet.

The following parameters must be saved in the profile for the VPI/VCI scan (when the xDSL 
connection is already established, the connection parameters, e.g. ADSL mode and target 
value, are locked).

Protocol-independent parameters:

The opening of test parameters is described in the chapter "Configuring accesses", see 
page 30.

Setting

Description

Test parameters:

VPI/VCI scan:

VPI 

Virtual path identifier:

VPI range that the ARGUS VPI/VCI scan tests.

Range: 0 to 255
Default: 

0 to 8

VCI

Virtual channel identifier: 

VCI range that the ARGUS VPI/VCI scan tests.

Range: 32 to 65535
Default: 

32 to 48

Number of 
scans

Number of scans. 

Range: 0 to 99
Default: 

2

Timeout

Maximum wait time for the response from the ATM network node to the test 
packet sent by ARGUS.

Range: 0.1 - 9.9 seconds
Default: 

0.5 seconds

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands