Argos Kids Sywell 228/8318 Assembly Instructions Manual Download Page 1

Page: 1 / 32

MADE IN

BRITAIN

Dimensions

Width - 104cm

Depth - 50cm

Height - 172cm

Kids Sywell -

3 Door Robe

Assembly Instructions -

Please keep for future reference

If you need help or have damaged or missing parts, call the

Customer Helpline: 08456 400800

Issue 5 - 31/10/14

Important -

Please read these instructions fully before starting assembly

ALR3021

246/7634

238/7460

228/8318

Issue 2 - 07/05/14 - Pins were going into the wrong surface of the Base.
Preparation of Top and Base are now separate steps.

Issue 3 - 23/07/14 - Changed Shelf to D2574A.

Issue 4 - 08/09/14 - Step 11 amended to show Backs being fitted.

Issue 5 - 31/10/14 - Argos code 238/9341 added to front page.

238/9341

Summary of Contents for Kids Sywell 228/8318

































Search results

Summary of Contents for Kids Sywell 228/8318

Reviews:

Related manuals for Kids Sywell 228/8318

Brands by name

Popular brands

Argos Kids Sywell 228/8318, Assembly Instructions Manual

Search results

Summary of Contents for Kids Sywell 228/8318

Reviews:

Related manuals for Kids Sywell 228/8318

Brands by name

Popular brands