P44x/EN CM/E33
Commissioning
Page 18/54
MiCOM P441/P442 & P444
5. SETTING
CHECKS
The setting checks ensure that all of the application-specific relay settings (i.e. both the
relay’s function and programmable scheme logic settings) for the particular installation have
been correctly applied to the relay.
If the application-specific settings are not available, ignore sections 5.1 and 5.2.
5.1
Apply Application-Specific Settings
There are two methods of applying the settings:
•
Transferring them from a pre-prepared setting file to the relay using a portable PC
running the appropriate software (see compatibility with S1 version in chapter VC) via
the relay’s front RS232 port, located under the bottom access cover, or rear
communications port (with a KITZ protocol converter connected). This method is the
preferred for transferring function settings as it is much faster and there is less margin
for error. If programmable scheme logic other than the default settings with which the
relay is supplied are to be used then this is the only way of changing the settings.
If a setting file has been created for the particular application and provided on a
diskette, this will further reduce the commissioning time and should always be the
case where programmable scheme logic changes are to be applied to the relay.
•
Enter them manually via the relay’s operator interface. This method is not suitable for
changing the programmable scheme logic.
5.2
Check Application-Specific Settings
The settings applied should be carefully checked against the required application-specific
settings to ensure they have been entered correctly. However, this is not considered
essential if a customer-prepared setting file has been transferred to the relay using a
portable PC.
There are two methods of checking the settings:
•
Extract the settings from the relay using a portable PC running the appropriate
software via the front RS232 port, located under the bottom access cover, or rear
communications port (with a KITZ protocol converter connected). Compare the
settings transferred from the relay with the original written application-specific setting
record. (For cases where the customer has only provided a printed copy of the
required settings but a portable PC is available).
•
Step through the settings using the relay’s operator interface and compare them with
the original application-specific setting record.
Unless previously agreed to the contrary, the application-specific programmable scheme
logic will not be checked as part of the commissioning tests.
Due to the versatility and possible complexity of the programmable scheme logic, it is
beyond the scope of these commissioning instructions to detail suitable test procedures.
Therefore, when programmable scheme logic tests must be performed, written tests which
will satisfactorily demonstrate the correct operation of the application-specific scheme logic
should be devised by the Engineer who created it. These should be provided to the
Commissioning Engineer together with the diskette containing the programmable scheme
logic setting file.
Summary of Contents for MiCOM P441
