8-30
4. From beneath the seat foam, remove the seat wire
from the two elastic loops; then remove the cover
from the seat base and seat foam.
INSTALLING
1. Position the cover over the seat foam and seat base;
then pull the two elastic loops through the slots in the
seat foam and secure with the seat wire. Check to
make sure it is positioned straight.
2. Fold the rear edge of the cushion down and around
the plastic base. Using a staple gun and 1/4 in. sta-
ples, staple the rear flap of the cushion to the plastic
base in the same areas as the original staples were
located. Position staples 1 in. apart.
3. Fold the sides of the cushion down around the bot-
tom edge of the plastic seat base. Position the staples
in the same area as the original staples were located.
NOTE: Note the cushion fit. If any wrinkles are
noted, remove by pulling the cushion material in the
appropriate direction before securing with staples.
4. Fold the front cushion material back and onto the
plastic seat base. Check for wrinkles and secure with
staples and two screws.
5. On the Bearcat/F-Series/T-Series, install the taillight
housing and secure with the screws.
6. Install the seat assembly (see appropriate Seat
Assembly in this section).
Taillight/Brakelight
Assembly
BEARCAT XT
1. Remove the four pins securing the rear seat to the
seat/Speedrack mount; then remove the seat.
0743-329
2. Compress the latch on the right side of the front seat
and lift the front seat away; then disconnect the tail-
light harness connector.
0743-444
3. Loosen (but do not remove) the three right-side seat/
Speedrack mount cap screws.
4. Carefully route the harness connector through the
hole in the storage compartment panel; then remove
the harness from beneath the seat/Speedrack mount.
5. Remove the two self-tapping screws securing the
taillight to the bumper; then route the harness out of
the bumper and remove the taillight.
6. Route the taillight harness through the bumper; then
secure the taillight to the bumper with the two self-
tapping screws.
7. Carefully route the harness beneath the Speedrack
mount and through the hole in the storage compart-
ment panel; then connect the harness connector.
8. Tighten the three right-side mount cap screws; then
lower the front seat.
9. Place the rear seat into position on the mount making
sure the four pin holes are properly aligned with the
mounting location on the mount.
10. Install the four pins making sure they are properly
seated.
F/M/XF
1. Remove the two torx-head screws securing the tail-
light to the taillight support; then disconnect the tail-
light harness connector.
PC103A
CAUTION
On Bearcat models, beneath the seat base is a dotted
guideline to follow when stapling the seat cover. Do
not staple inside this guideline or perforation of the
gas tank may occur.
! WARNING
Make sure the rear seat is securely locked in place
with the four pins before carrying a passenger or per-
sonal injury may result.
Summary of Contents for Sno Pro 120
