background image

15

3. Push the stud through the hole from

inside the track; then place the

domed support plate and lock nut on

the exposed stud.

4. Using a wrench to secure the stud,

tighten the lock nut on the exposed stud.

It is also recommended that whenever

studs are installed on a track, carbide

wear bars should be installed on the skis.

Carbide wear bars complement the track

studs to balance steering control under

these conditions. The length of the car-

bide on the wear bars should be propor-

tionate to the number of track studs (i.e.,

small number of track studs = short

length of carbide and many track studs =

long length of carbide). The proper pro-

portion between the number of studs and

carbide length on the wear bar will main-
tain steering balance.

Reverse Operation

The engine reverse function offers the

operator the convenience of being able to

back up the snowmobile rather than hav-

ing to turn the snowmobile around by

hand. This feature, under most situations,

should not be used to free a stuck snow-

mobile as it will tend to dig the skis

deeper into the snow. Always use mini-

mal speed when operating in reverse. 

Shifting Into Reverse

ONS-314

1. Always warm up the engine for 2-3

minutes prior to shifting into reverse.

The reverse function is canceled when

engine temperature is below or above

normal operating range.

2. Shift only with the engine at idle

RPM and the snowmobile com-

pletely stopped.

3. If attempting to shift into reverse at

too high engine RPM (above 3000

RPM), the reverse function will be

canceled. This indicates the reverse

switch button was pressed at too high

RPM. The operator must reduce

engine RPM below 3000 and press

the button a second time.

4. Upon pressing the reverse switch

button, the reverse function will

make up to three attempts to engage

into reverse. If the function is not

completed after the third attempt,

the engine will shut down.

! WARNING

Never rotate a damaged track under

power and never perform track mea-

surements, adjustments, and/or

maintenance with the engine running.

! WARNING

Always balance the snowmobile with

the proper proportion between the

number of studs and carbide length

on the wear bars. Do not “over drive”

conditions; use common sense in all

operating conditions.

CAUTION

Do not use studs that are more than

9.525 mm (0.375 in.) longer than the

track lug height.

! WARNING

Do not operate a snowmobile with

loose studs as they may be thrown

from the track. Always use a shielded

safety stand whenever performing

any maintenance or adjustments.

! WARNING

DO NOT stand behind the snowmo-

bile or near the rotating track. NEVER

run the track at high speed when the

track is suspended.

CAUTION

Never shift into reverse while the

snowmobile is moving forward as it

is hard on the driven clutch.

Summary of Contents for 2262-967



















































Reviews:

Related manuals for 2262-967