background image

10

Gauge

ZR-393A

1. Left Button — Shifts top display

through speedometer and RPM.

2. Middle Button — Shifts middle dis-

play through speedometer, RPM,

clock, odometer, trip 1, trip 2, and

engine hours.

3. Right Button — Shifts bottom dis-

play through coolant temperature,

battery voltage, intake air tempera-

ture, exhaust temperature, and fuel

level.

4. Speedometer/Tachometer Display

— Indicates approximate vehicle

speed in MPH or KM/H when the

speedometer function is selected,

and RPM when the tachometer func-

tion is selected. Press the Left But-

ton to change which parameter is

being displayed. With speedometer

selected, press and hold the Left

Button to shift between standard

(MPH/miles/Fahrenheit) and metric

(km/h/kilometers/Celsius).

5. Engine Hour Meter/Odometer/Trip

Meter/Speedometer/Tachometer/

Clock Display — Displays engine

hours, odometer, trip meter, speed-

ometer, tachometer, or clock. Press

the Middle Button to change which

parameter is being displayed. The

Engine Hour Meter and Odometer

cannot be reset. To reset the trip

meter, select the Trip Meter; then

press and hold the Middle Button

until the trip meter display reads 0.

With the clock mode selected, press

and hold the Left Button to set the

clock. The option of selecting the

12-hour or 24-hour clock is avail-

able; press the Left Button to alter-

nate between the two modes. Next,

press the Middle Button to set the

clock. Press the Left or Right to set

the hours; then press the Middle

Button to set the minutes. Press the

Left or Right Button to set the min-

utes. When the proper time has been

set, press the Middle Button to

return to the main gauge display.

6. Coolant Temperature/Battery Volt-

age/Intake Air Temperature/Exhaust

Temperature/Fuel Level Display —

Displays coolant temperature, bat-

tery voltage, intake air temperature,

exhaust temperature and fuel quan-

tity. Press the Right Button to

change which parameter is being

displayed. Press and hold the Right

Button to see the actual values asso-

ciated with the mode selected.

7. Gear Position Indicator — Indicates

the gear the transmission is in.

8. Coolant Temperature Indicator —

When the snowmobile is started, this

indicator will flash and LOW TEMP

will be displayed until the engine

reaches operating temperature. 
If the coolant temperature rises too

far above proper operating tempera-

ture, the indicator will flash a warn-

ing (alert). If the coolant

temperature rises to a critical point

above proper operating tempera-

ture, the indicator will cease flashing

and will remain constantly illumi-

nated.

CAUTION

If the indicator is illuminated, stop the

engine immediately and allow it to cool

down. If unable to either determine or

remedy the problem, take the snowmo-

bile to an authorized Arctic Cat Snow-

mobile dealer for service. If not under

warranty, this service is at the discretion

and expense of the snowmobile owner.

Summary of Contents for 2262-967



















































Reviews:

Related manuals for 2262-967