Arctic Cat 2012 700 i Cruiser Operator'S Manual Download

Page: 84 / 708

Div

ision I -

Rid

arenes

s/Re

spons

ibility

Main Table of Contents

Section Table of Contents

Ne xt

Prevention

Long Pants and Long Sleeved Shirt

The goal is to protect your body from branches, long grass, airborne

objects, or anything else that could scrape your skin. The more thick

and durable the material, the better protection it’ll provide.

Gloves

Your hands are targets for flying objects and branches. Along with

providing skin protection, gloves will shield your hands from harsh

weather. Wear gloves that are weather resistant and have a gripping

surface to keep them from sliding off the handlebar.

Boots/Ankle Protection

Wear a boot that covers the largest possible area of your leg (prefera-

bly up to your knee) and can handle significant impact. Choosing

boots with low heels and a good tread will help prevent your feet

from slipping off the footrests in wet or rugged conditions or getting

hurt if they get hit by rocks, dirt, or branches.

The second step in Prevention is checking the condition of your ATV.

Chances are good that you’ll be using your ATV in some rough terrain,

and there’s no way you want your brakes to go out when riding downhill.

You need to check the following parts on your ATV before every ride.

1. Tires and Wheels
2. Controls and Cables
3. Lights and Electrical
4. Oil and Fuel
5. Chassis and Drive Train
6. Miscellaneous Items

One easy way to remember what parts you need to check is by using

the acronym “T-CLOC.” It stands for:

1. Tires and Wheels

Correct tire pressure is crucial. Consult the

General Maintenance section of this Opera-

tor’s Manual for tire pressure guidelines.

Incorrect tire pressure can cause poor han-

dling, instability, and a loss of ATV control.
While checking the tire pressure, inspect the tread and sidewalls of

the tires for cracks, cuts, or other damage that could indicate they

need to be replaced.

2. Controls and Cables
A. Brakes

Squeeze your hand brake levers. If they feel

soft or “squishy,” the brakes may need

adjustment. Check the maintenance section

of this Operator’s Manual for instructions.

Don’t use the ATV until the brakes are oper-

ating normally.
Test the brake lever lock and see if it locks the hand brake lever into

position; then disengage it to release the brakes. Ensure that the hand

brakes are working properly; your brakes could fail during a ride if

they’re not maintained.

B. Throttle

The throttle should have a free, smooth

range of motion. If it seems to “stick” at any

point, refer to the General Maintenance sec-

tion of this Operator’s Manual for instructions. Driving your ATV

with a sticking throttle can turn your leisurely ride into an unwelcome

accident. Don’t drive your ATV if the throttle sticks.

Condition of the ATV

IRES AND

WHEELS

ONTROLS

AND CABLES

IGHTS AND

ELECTRICAL

IL AND

FUEL

HASSIS AND

DRIVE TRAIN

Check:

1. Tire pressure
2. Tire surface (tread

and sidewalls)

Check:

1. Hand brake levers
2. Parking brake

Check:

1. Free, smooth range

of motion

2012 T-14

Summary of Contents for 2012 700 i Cruiser





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 700 i Cruiser

Reviews:

Related manuals for 2012 700 i Cruiser

Brands by name

Popular brands

Arctic Cat 2012 700 i Cruiser, Operator'S Manual

Search results

Summary of Contents for 2012 700 i Cruiser

Reviews:

Related manuals for 2012 700 i Cruiser

Brands by name

Popular brands