manualshive.com logo in svg

Arcos Burn Navigator Active, User Manual

Share
Download
Arcos Burn Navigator Active User Manual Download Page 8

 

Burn Navigator® User’s Manual 

Page 8 

First-time Operation 

 

 

AC-USB 3.1 Adapter (1) 

& USB A-to-C 3.5’ Cable (1) 

 

 

 

CMP-1805 

 

Protective Cover (1) 

 

 

 

CMP-1803 

 

Battery Pack (1) 

 

 

 

CMP-1806 

 

 

 

 

Stylus (1)  

 

 

 

CMP-1804 

 

Installing or Replacing the Battery 

The tablet ships with a battery pre-installed. To replace the battery, do the following: 

1.

 

Power off the tablet. 

2.

 

Remove the protective cover from the tablet. 

3.

 

Remove the battery compartment cover. 

4.

 

Remove the old battery if present. 

5.

 

Insert the new battery with the label facing up and the battery terminals aligned with the contact pins on 

the device. 

6.

 

Replace the battery compartment cover and protective cover. 

 

CAUTION 

•

 

Make sure the battery compartment cover is securely snapped in place when carrying the device. 

•

 

Do not expose the battery to water or any other liquid. 

•

 

Do not attempt to charge the battery using methods other than specified. Do not short the battery 

terminals. Do not attempt to overcharge the battery. 

•

 

Do not touch the terminals on the battery pack or the tablet. Doing so can make the terminals dirty or 

damaged and may cause malfunction of the battery pack and/or the tablet. 

•

 

Monitor the device for signs of battery failure, such as frequent overheating, or swelling of the battery 

pack. Continued use of a failing battery may cause permanent damage to the tablet, and creates risk of 

fire. Stop use of the tablet immediately and replace the battery if failure is suspected. 

 

 

 

Summary of Contents for Burn Navigator Active





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands