background image

N80ESN/N80ESL(Series A): Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

31

GENERAL

These instructions are written as if the furnace is installed in an upflow

application.  An  upflow  furnace  application  is  where  the  blower  is

located below the combustion and controls section of the furnace, and

conditioned air is discharged upward. Since this furnace can be installed

in any of the 4 positions (see 

Fig. 5

), you must revise your orientation to

component location accordingly.

ELECTRICAL CONTROLS AND WIRING

The  electrical  ground  and  polarity  for  115-v  wiring  must  be  properly

maintained. Refer to 

Fig. 24

 for field wiring information and to 

Fig.

 for

furnace wiring information.

NOTE: 

If the polarity is not correct, the STATUS LED on the control

will  flash  rapidly  and  prevent  the  furnace  from  heating.  The  control

system also requires an earth ground for proper operation of the control

and flame-sensing electrode. 

The 24-v circuit contains an automotive-type, 3-amp. fuse located on the

control (see 

Fig. 28

). Any shorts of the 24-v wiring during installation,

service, or maintenance will cause this fuse to blow. If fuse replacement

is required, use ONLY a 3-amp. fuse. The control LED will display off

when fuse needs to be replaced. 
Proper  instrumentation  is  required  to  service  electrical  controls.  The

control  in  this  furnace  is  equipped  with  a  Status  Code  LED

(Light-Emitting  Diode)  to  aid  in  installation,  servicing,  and

troubleshooting. Status codes can be viewed at the sight glass in blower

access  door.  The  furnace  control  LED  is  either  ON  continuously,

flashing a heartbeat, or a status code.
For  an  explanation  of  status  codes,  refer  to  service  label  located  on

blower access door, or 

Fig. 44

 and the troubleshooting guide which can

be obtained from your distributor. 
See 

Fig. 51

 for a brief Troubleshooting Guide. 

CARE AND MAINTENANCE

For  continuing high performance and  to minimize  possible  equipment

failure,  periodic  maintenance  must  be  performed  on  this  equipment.

Consult your local dealer about proper frequency of maintenance and the

availability of a maintenance contract.

The minimum maintenance on this furnace is as follows: 

1. Check and clean/replace air filter each month or more frequently if

required. Replace if torn.

2. Check  blower  motor  and  wheel  for  cleanliness  each  heating  and

cooling season. Clean as necessary.

3. Check electrical connections for tightness and controls for proper

operation each heating season. Service as necessary.

4. Inspect  burner  compartment  before  each  heating  season  for  rust,

corrosion,  soot  or  excessive  dust.  If  necessary,  have  furnace  and

burner serviced by a qualified service agency.

5. Inspect  the  vent  pipe/vent  system  before each  heating  season  for

rust,  corrosion,  water  leakage,  sagging  pipes  or  broken  fittings.

Have vent pipes/vent system serviced by a qualified service agency.

6. Inspect any accessories attached to the furnace such as a humidifier

or electronic air cleaner. Perform any service or maintenance to the

accessories as recommended in the accessory instructions. 

WARNING

!

ELECTRICAL SHOCK, FIRE OR EXPLOSION HAZARD

Failure to follow this warning could result in personal injury or death.

Before  installing,  modifying,  or  servicing  system,  main  electrical

disconnect switch must be in the OFF position and install a lockout tag.

There  may  be  more  than  one  disconnect  switch.  Lock  out  and  tag

switch  with  a  suitable  warning  label.     Verify  proper  operation  after

servicing.

CAUTION

!

ELECTRICAL OPERATION HAZARD

Failure to follow this caution may result in improper furnace operation

or failure of furnace. 

Label all wires prior to disconnection when servicing controls. Wiring

errors can cause improper and dangerous operation.

WARNING

!

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury or death.

There  may  be  more than  one electrical supply to the furnace. Check

accessories and cooling unit for additional electrical supplies that must

be shut off during furnace servicing. Lock out and tag switch with a

suitable warning label.

WARNING

!

FIRE OR EXPLOSION HAZARD

Failure  to  follow  this  warning  could  result  in  personal  injury,  death

and/or property damage. 

Never store anything on, near, or in contact with the furnace, such as: 

1.Spray or aerosol cans, rags, brooms, dust mops, vacuum cleaners, or

other cleaning tools.

2.Soap powders, bleaches, waxes or other cleaning compounds, plastic

or  plastic  containers,  gasoline,  kerosene,  cigarette  lighter  fluid,  dry

cleaning fluids, or other volatile fluids.

3.Paint  thinners  and  other  painting  compounds,  paper  bags,  or  other

paper products.

WARNING

!

ELECTRICAL SHOCK AND FIRE HAZARD

Failure to follow this warning could result in personal injury, death or

property damage. 

Turn off the gas and electrical supplies to the unit and install lockout tag

before  performing  any  maintenance  or  service.  Follow  the  operating

instructions on the label attached to the furnace.

WARNING

!

CARBON MONOXIDE POISONING AND FIRE 

HAZARD

Failure  to  follow  this  warning  could  result  in  personal  injury,  death

and/or property damage. 

Never operate unit without a filter or with filter access door removed.

CAUTION

!

CUT HAZARD

Failure to follow this caution may result in personal injury. 

Sheet metal parts may have sharp edges or burrs. Use care and wear

appropriate  protective  clothing,  safety  glasses  and  gloves  when

handling parts and servicing furnaces.

Summary of Contents for A Series









































Reviews: