ARCIMOTO FUV 2022 Owner'S Manual Download

Page: 112 / 194

page 110

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290 • docID: P10001

This will update the screen again, with a green check mark

replacing the Startup Button graphic:

Once the FUV is started, release the START button.

Once started, the Display changes to show the Drive

screen. At this point, the FUV is started and is ready to

drive.

NOTE

If the FUV does not start, release the button, re-apply pressure
to the Brake Pedal, and try again.

If the HV Power, 12V Power or Brake Failure indicators remain
lit after the FUV is started, turn off the FUV and contact
Arcimoto for assistance at 541-780-0032.

Release the Parking Brake

The Parking Brake must be released before driving.

Don’t drive until the parking brake is fully disengaged. Driving
the FUV with the parking brake engaged or partially engaged
can damage the brakes.

With the Brake pedal depressed, press the Parking Brake

button on the Control Panel:

OPERATION

Summary of Contents for FUV 2022



































































































































































































Search results

Summary of Contents for FUV 2022

Reviews:

Related manuals for FUV 2022

Brands by name

Popular brands

ARCIMOTO FUV 2022, Owner'S Manual

Search results

Summary of Contents for FUV 2022

Reviews:

Related manuals for FUV 2022

Brands by name

Popular brands