manualshive.com logo in svg

ARCBRO Stinger Series, User Manual, Page: 63 / 77

Share
Download
ARCBRO Stinger Series User Manual Download Page 63

Service Support Spirit                 

 

 

 

Unique Solution                                    

  WWW.ARCBRO.COM

 

 

63 

8. LIBMINIT (Library of Patterns) 

8.1. LIBMINIT Setting 

In addition to customized pattern module, the feature allows user to input the intended dimensions and 

get the expected work piece.   
When entering parameter, the control system will conduct general check to the physical dimensions and 
prompt warning message if any error is detected.   
Notes:  

1.

 

It is impossible for the control system to find all the error parameters; therefore, please enter correct 
dimensions for parameters as much as possible.  

2.

 

When the parameters are entered, the control system will drawn the pattern based on the entered 
parameters, which is very helpful to graphic check.   

In the system main menu, press [F6] to enter the LIBMINIT(Library of Patterns).   

 

Fig. 8.1 LIBMINIT Feature(Library of Patterns) 

Summary of Contents for Stinger Series














































































Reviews:

No comments