manualshive.com logo in svg

ARCBRO Stinger Series, User Manual, Page: 54 / 77

Share
Download
ARCBRO Stinger Series User Manual Download Page 54

Service Support Spirit                 

 

 

 

Unique Solution                                    

  WWW.ARCBRO.COM

 

 

54 

BACKWARD/FORWARD SPEED  -----  If this option is enabled(value:1), the system will not decelerate 
through a circular transition when the running direction change of system between program segments is 
within the conversion angle of corner speed, as shown in the figure below.  

SPD TRAN ANGLE ---- When the change of the running direction between blocks exceeds this angle, when 
the system is at the corner, it will decelerate to the starting speed.   

Generally, when the machine is heavier, select a smaller value. The adjustment can be determined 

according to the processing speed and the vibration of the machine tool. 

If the vibration is large, select a small value; 

 

CORNER RADIUS ----See ARC RADIUS 

ARC SPEED ---- Speed limit only for arc 

ARC RADIUS----

 

Arc radius setting, Used in conjunction with parameter arc speed limit, When the arc radius 

is less than this value, it runs at the arc speed limit; when it is set to 0, the arc speed limit function is invalid; 

7.2.2 System parameters 

In the SETUP submenu, press [F2] key to enter system parameters setting window, as shown in Fig.7.3.  

Summary of Contents for Stinger Series














































































Reviews:

No comments