background image

SPECIFICATIONS

MOTOR:

Type

Submersible

Gallons Circulated

40 GPM/2400 GPH

Voltage

110/115 Volts
220/240 Volts (Export Only)

Frequency

60 Cycle-50 Cycle

Speed

1725/1425 RPM

Bearing

Ball Bearing

Housing

Aluminum Anodized

Motor Seals

Double Lip Wave

Overload Protection

Thermal Overload

Electrical Cord

#l6 Wire Encased in Flotation Jacket;
55' & 75' in length

DRIVE:

Reduction

80:1

Reduction Unit

Worm Gear-Bronze Gear

Reduction Gear Lubrication

Permanent

Reduction Unit Housing

20% Glass Filled Resin

Rear Wheel Drive

Planetary Gear System

Front Wheel Drive

Continuous Belt

FILTER

:

Type

Self Contained and Attached to Cleaner

Filter Media

Corrugated Resin Impregnated Element

Porosity

50 Microns

Filter Area

20 Square Feet

Housing

Molded Plastic

CASTINGS

:

All castings are corrosion resistant Aluminum Alloy.

SHAFT and AXLE:

All parts such as axle, shafts, pins, fasteners, rods, etc., are corrosion resistant.

FLOATING ELECTRICAL CONDUCTOR:

Standard lengths are 55' and 75'.

DIMENSIONS:

Height

161/2" (41.9 cm)

Width

16" (40.6 cm)

Length

18" (45.7 cm)

WEIGHT

:

Net Weight of MakoShark 2 with 60' Cord

34 lbs. (17.2 kg)

Gross Shipping Weight

38 lbs. (19.5 kg)

Net Weight of MakoShark 2 with 80' Cord

36 lbs. (19.5 kg)

Gross Shipping Weight

40 lbs. (21.7 kg)

SHIPPING CARTONS:

Cleaner

191/2" x 171/2" x 16"
(49.5 cm x 44.5 cm x 40.6 cm)

9

Summary of Contents for Mako Shark 2

















Reviews: