background image

Copyright © 2018 Aqua Creek Products All Rights Reserved

Revised 6/8/18

Scout 2

Pool Lift

Check entire box and inside all packing materials for parts. Before beginning assembly, read the 

instructions and identify parts using the fi gures and parts listed in this document.

It is critical all parts be carefully inspected by the installer prior to installation to ensure no 

damage occurred in transit and a damaged part is not used. If any damage occurred in transit, 

Aqua Creek Products, LLC must be notifi ed within three days of receipt of unit. 

Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s 

warranty and may affect the safety of the user.

READ CAREFULLY

PART #: F-802SC2

US PATENT NUMBER: [D507,769 S]

375 LB. [170 kg] MAXIMUM WEIGHT CAPACITY

MANDATORY 

 

LEAVE THIS MANUAL WITH LIFT OWNER

Read and follow all instructions

Lift safety can only be ensured if the lift is installed and 

operated according to these instructions.

• 

NEVER permit children to play on or around the lift

•  Do not allow children to use the lift without adult 

supervision

•  NEVER apply direct water pressure to the electronics
•  NEVER use the lift with a dry pool
•  For safety reasons, NEVER swim alone
• 

NEVER manually rotate the lift

ADA COMPLIANT

1

Summary of Contents for Scout 2


















Reviews: