APW Wyott EF-30i Installation And Operating Instructions Manual Download Page 1

1

DESIGNED SMART. BUILT SOLID.

®

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and 

liquids in the vicinity of this or any other appliance.

WARNING: Improper installation, operation, service or maintenance can cause 

property damage, injury or death. Read and understand these instructions 

thoroughly before positioning, installing, maintaining or servicing this equipment.

WARNING: Initial heating of oven may generate smoke or fumes and must be done 

in a well-ventilated area. Overexposure to smoke or fumes may cause nausea or 

dizziness.

APW Wyott Food Service Equipment Company

1307 N. Watters Road, Suite 180 • Allen, TX 75013

APW Wyott Food Service Equipment Company is a wholly owned subsidiary of Standex International Corporation.

972.908.6100 Phone 

+1.800.527.2100

214.565.0976 Fax 

www.apwwyott.com

INSTALLATION AND OPERATING INSTRUCTIONS

Electric Fryers

Model: EF-30i

P/N 882209 REV A 11/18

WARNING: California Residents Only. This product can expose you to chemicals including 

chromium which is known to the State of California to cause cancer and birth defects or 

other reproductive harm. For more information go to www.P65Warnings.ca.gov. 

Summary of Contents for EF-30i


















Reviews: