background image

 

 

11 

3.3

 

INTENDED USE 

The pneumatic seeders of types PS 120 to PS 500 serve to spread seed with different properties and grain 
sizes on open fields. 
The implements are designed solely for normal use in agricultural operations. Only cereal varieties that 
are intended by the manufacturer and listed in the operating manual may be used. Different seeding shafts 
are designed for the different cereal varieties, which must be used and replaced if necessary. A special 
version of the seed drill protected against corrosion can also be used for spreading fertiliser with a seeding 
shaft designed for this purpose (intended use). 
Any other use is considered to be non-intended. The manufacturer is not liable for any resulting damage, 
the operator alone bears the associated risk.   
Intended  use  also  includes  compliance  with  the  conditions  for  operation,  maintenance,  and  repairs 
prescribed by the manufacturer.   
The  applicable  accident  prevention  regulations  as  well  as  the  other  general  safety-related  and 
occupational health regulations must also be observed.   
The manufacturer is not liable for any damage resulting from unauthorised modifications and the use of 
components and auxiliary parts. 

 

3.4

 

PERSONNEL REQUIREMENTS 

The  owner  is  responsible  for  ensuring  that  the  implement  only  be  used,  maintained  and  repaired  by 
persons who have relevant experience and were instructed on the risks. This must be verified by the owner 
at regular intervals. 
The safety instructions must also be handed over to other users. 

Qualification 

Persons who will be handling the seed drill must fulfil the following requirements: 

Personnel 

Activities 

Required qualification 

Forwarder 

 

Transport of the seed drill from 
one business to another 

 

Experience with transport of 
machinery 

 

Qualification of a transport 
specialist for machinery

 

Transporter 

 

Transport of the implement within 
the farm 

 

Forklift driver 

 

Experience with handling the 
suitable lifting gear

 

Installer 

 

Installation and commissioning of 
the seed drill 

 

Trained mechanic 

Setter 

 

Setting up the seed drill 

 

Experience in the agricultural field 

 

Experience with handling the 
seed drill

 

Operator 

 

Operating the seed drill on the 
farm 

 

Cleaning the seed drill

 

 

Trained assistant 

 

Suitable driving license 

Maintenance personnel 

 

Performing maintenance work 

 

Performing repair work

 

 

Trained mechanic 

Disposer 

 

Disposal of the seed drill 

 

Disposal specialist 

 

 

 

3.5

 

PERSONAL PROTECTIVE EQUIPMENT 

The personnel must be equipped with the following personal protective equipment and wear it if necessary: 

 

Hearing protection 

 

Mask 

 

Safety shoes with non-slip soles 

 

Summary of Contents for PS 120 M1

















































Reviews: