Aproli 280/700 STRONG Installation Manual Download Page 8

Page: 8 / 12

FEATURES OF THE ELECTRONIC PROGRAMMER ELPRO 13 CEI FOR

SWINGING GATES

All the electrical connections are to be made as per the following instructions and diagrams. Supply the terminals 24-25 with 230V -
50 Hz single phase voltage. The “red LED” switches on and stays on as long as the board is properly supplied. Through the timer No. 9
you can control the running time of the motor in both cycles, OPEN and CLOSE.
Set it so that the running time of the motor is longer than the actual travel of the gate: set the timer No. 8 -DWELL- ie. the interval between
open and re-closing, so that you can meet the required interval of time. The timer No. 7 -LEAF DELAY in “close” cycle- is to be set as
follows: on to “–” (less) the delay is out of service; clockwise on to “+” (more) the delay is operative.
- With the electric motor connected to terminals 19 - 20 - 21: the delay is operative in the “open” cycle, with a factory pre-set time.
- With the electric motor connected to terminals 16 - 17 - 18: the delay is operative in “close” cycle and can be adjusted through the
timer No. 7 on to “less” or “more”.
LOGIC OF THE ELECTRONIC PROGRAMMER: When a pulse is given, the flashing light switches on. After three seconds the motors start.
During the interval before re-closing, the light stays on. When the gates are fully re-closed, the light keeps on flashing for three more
seconds and then switches off automatically.
The 3 second interval (pre-flashing) which precedes the actual start of the motors can be eliminated by means of the DIP-SWITCH “B” No.4.

LED No. 1: It switches on when voltage is supplied.
LED No. 2: “PHOTOCELLS”. Normally on. It switches off when the photocells are obstructed.
LED No. 3: “OPEN”. It switches on when the respective switch is activated.
LED No. 4: “CLOSE”. It switches on when the respective switch is activated.
LED No. 5: “STOP”. Normally on. It switches off when the respective switch is activated.
LED No. 6: “RADIO”. It switches on whenever a pulse is given, either from remote control, keyswitch or push buttons.

DIP-SWITCH B SETTING IN ELPRO 13 CEI
N

1 OFF = PHOTOCELLS. NO STOP IN OPEN CYCLE. REVERSE/CLOSE

2 OFF = REMOTE CONTROL. REVERSE

3 OFF = NO AUTOMATIC RECLOSING

4 OFF = NO PRE-FLASHING

5 OFF = REMOTE CONTROL. NO STOP AND HOLD AS LONG

AS BUTTON DOWN. IT OPENS STRAIGHT AWAY

6 OFF = BOTH LEAFS ARE OPERATED

7 OFF = S. R. P. OUT OF SERVICE

8 OFF = LEAF DELAY OPEN CYCLE.

ONE STARTS BEFORE THE OTHER

LAMP ON

= GATE OPEN

LAMP FLASHES SLOWLY = GATE OPENING
LAMP FLASHES FAST

= GATE CLOSING

LAMP OFF

= GATE CLOSED

1) It is advisable not to expose the control box directly to weather conditions; if mounted outside, a suitable enclosure is recommended

to protect it from sunshine and rain.

2) Bridge terminals 1 - 2 if you do not require any photocells.
3) Should two sets of photocells be required, these are to be series connected to terminals 1 - 2, contact normally closed.
4) Bridge terminals 6 - 8 if you do not require any keyswitch or push buttons.
5) Fit the mains to the control box with a high sensitivity, differential, magnetic-thermal switch, 0.03 Amps.
6) OPERATING MODE WITH TWO PAIRS OF PHOTOCELLS, INDEPENDENT FROM EACH OTHER

Dip-switch No. 1 set to OFF, connect the pair of photocells that are inside the property to the terminals marked “2

pair”.

The second pair always stops the gate in open cycle in case of an obstacle.
During close cycle the second pair reverses the gate direction.

7) NOTE WELL

FAULT FINDING:
- Check supply voltage with a tester: it must be 230 V, single-phase.
- Check the high voltage fuses.
- Check the low voltage fuses.
- Check if the photocell contacts are normally closed.
- Check voltage from the control box to the electric motor(s): power might have dropped.
- The section of the electric cables to the motor(s) must not be less than 1.5 mm

- Connect the other pair to the terminals 1 - 2
This pair performs in the standard pre-set mode, ie:
no stop during open cycle, REVERSING GATE DIRECTION DURING CLOSE CYCLE.
Terminals to stay linked out should the second pair of photocells not be used, and set the desired operating mode through Dip-switch No. 1.

* 24 V ~ output. Terminals 12 - 13. It can supply power for 2 pairs of photocells plus 1 radio receiver.

Terminal 11 provides a power output for a lamp. 24 V - 3 W max.
Flashing lamp output. Terminals 22 - 23. Maximun available power 25 W max.

1 ON = STOP DURING OPEN CYCLE

2 ON = NO REVERSE DURING OPEN CYCLE

3 ON = AUTOMATIC RECLOSING

4 ON = PRE-FLASHING

5 ON = STOP AND HOLD AS LONG AS

THE BUTTON IS KEPT DOWN

6 ON = PEDESTRIAN. ONE LEAF ONLY

GATES IN CLOSE POSITION

7 ON = S. R. P. IN SERVICE

GATES IN CLOSE POSITION