APRILIA TUAREG 660 Service Station Manual Download Page 258

Page: 258 / 311

•

Rotate the pin (8) to release the brake

pump control rod and slide it out in or-

der to remove it.

•

Unscrew the two fastening screws (9)

of the rear brake master cylinder and

remove it.

Installazione

To install the rear master cylinder, carry out the procedures described above in reverse order. Then fill

the system and bleed it.

PAY ATTENTION TO USE NEW WASHERS TO FASTEN THE SCREW OF THE BRAKE LINE.

Brake system lines

Removal

To remove the fuel pipes it is necessary to first remove the fuel tank, the side fairings and the right side

protection of the frame. Then drain the entire brake system and proceed as described:

MODULATOR - REAR BRAKE CALLIPER

BRAKE LINE

•

Unscrew the fixing screw (1) with the

two washers (2).

Braking system

TUAREG 660

BRAK SYS - 258

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands