APRILIA TUAREG 660 Service Station Manual Download Page 199

Page: 199 / 311

•

Position the frame cover (13) and after

having positioned the four screws (14)

tighten them to torque.

•

Restore the drive chain to the correct tension, following the specific procedure described in

the "Adjustment" paragraph.

Drive chain

Removing

The transmission chain, although "closed", has a

different coloured hammerlock (where provided),

which should be used to perform opening / disas-

sembling procedures.

NOTE

WHERE PRESENT, THE HAMMERLOCK (1) MAY ALSO BE
IDENTIFIED BY A SIGN (2) APPLIED IN THE MOUNTING
LINES DURING MANUFACTURING.

To dismantle and remove the chain, proceed as

follows:

•

Partially remove the pins (3) using a

generic chain breaker.

TUAREG 660

Chassis

CHAS - 199

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands