APRILIA SL 750 SHIVER Service Station Manual Download Page 88

Page: 88 / 303

•

Check the VEHICLE connector of the Marelli control unit, the filter housing large connector

and the throttle control unit connector: if not OK, restore. If OK, check continuity between

the Marelli control unit and the throttle control unit connector from VEHICLE PIN 55 to PIN

B7 and from PIN 56 to PIN A7: if not OK, restore. If OK, check that with throttle control unit

connector disconnected and with key set to ON, there is no voltage on PINS A7 and B7: if

there is voltage, replace the cable harness. If there is no voltage, check that PINS A7 and

B7 are insulated from ground connection: if they are not insulated from the ground connec-

tion, replace the cable harness. If they are insulated, replace the throttle control unit or the

Marelli control unit.

AXONE: NOTES

After installing the control unit and setting the key to ON, wait for 3 seconds, time during which the

control unit detects the throttle valve position.

Connect to Axone and check that the status for

Throttle Self-learning is Carried out

and the status

for

Throttle grip autodetection is Not carried out

(this last status entails Urgent service being dis-

played on the instrument panel).

If Throttle Self-learning shows

Not carried out

, go to stage 1. If it shows

Carried out

, go to stage 2.

Stage 1:

current errors have probably been detected by the control unit: solve these malfunctions and

check the Throttle Self-learning status again. Throttle Self-learning can also be checked from the Pa-

rameter adjustment (screwdriver and hammer) screen page.

Stage 2

: Carry out the Throttle Self-learning from the Parameter adjustment (screwdriver and hammer)

screen page and check that Throttle Self-learning status is Carried out. If it is not correct or the voltage

detected on the throttle is out of scale (check with Axone) or if current errors are probably detected by

the control unit: solve these malfunctions and repeat the procedure.

Battery

Characteristic

Battery

12V - 10 Ah

Battery installation

NOTE

Electrical system

SL 750 SHIVER

ELE SYS - 30

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 88 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: