manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 87 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 87

PARAMETERS

Target idle rpm

AXONE: ELECTRICAL ERRORS

EEPROM Error P0601

 - circuit not operational.

Error cause

•

Replace injection ECU. The instrument panel does not indicate the presence of this error

even in the ATT status.

RAM Error P0604-

 circuit not operational.

Error cause

•

Replace injection ECU. The instrument panel does not indicate the presence of this error

even in the ATT status.

ROM Error P0605-

 circuit not operational.

Error cause

•

Replace injection ECU. The instrument panel does not indicate the presence of this error

even in the ATT status.

A/D converter P0607-

 circuit not operational.

Error cause

•

Replace injection ECU.

Level 2 safety reset P0608

Error cause

•

As the level 2 safety system (comparison between requested torque and calculated torque)

has detected a fault, the control unit has reset engine (C gravity).

Troubleshooting

•

Continue failure search for the other errors detected .

Safety Engine Stop P0609

Error cause

•

As the level 3 safety system (control EEPROM) has detected a fault, the control unit has

shut off the engine (D gravity).

Troubleshooting

•

Replace Marelli control unit.

Reset lines error P0610-

 circuit not operational

Error cause

•

Problems on the reset lines (PINS 55 and 56 of the VEHICLE connector) of the throttle

motors: lines used to interrupt motor functioning for safety reasons.

Troubleshooting

SL 750 SHIVER

Electrical system

ELE SYS - 29

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments