APRILIA SL 750 SHIVER Service Station Manual Download Page 84

Page: 84 / 303

KM / MILES

This menu selects the unit of measurement, either for the speed or the total or partial odometers.

•

MILES

LANGUAGES

Select the user interface language from this menu.

•

ITALIANO

•

ENGLISH

•

FRANCAIS

•

DEUTSCH

•

ESPAGNOL

Service warning light reset

VEHICLE SERVICING RESET

This function is used to reset vehicle servicing. Using this function, the odometer can be reset only once

within the first 200 km (124 mi) of the vehicle, provided this has not been done by the Quality Check.

In order to activate this function follow the instructions in the DIAGNOSIS section.

See also

Diagnosis

level indicators

Fuel reserve sensor

Check proper operation of the sensor by adding a 2W bulb in series to the sensor.

Place a bulb between the battery power supply cable and the connector terminal and connect the

negative terminal to the ground connection:

•

if the sensor is submerged in petrol (sensor high electrical resistance, approx. 5-7 kOhm),

the bulb should remain off.

•

if the sensor is not submerged in petrol, the bulb should turn on.

Electrical system

SL 750 SHIVER

ELE SYS - 26

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 84 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: