APRILIA SL 750 SHIVER Service Station Manual Download Page 82

Page: 82 / 303

•

INCORRECT CODE

and the instrument panel goes back to the main menu. Otherwise, the following menu is displayed:

•

EXIT

•

ECU DIAGNOSIS

•

INSTRUMENT PANEL ERRORS

•

ERROR CLEARING

•

VEHICLE SERVICING RESET

•

UPDATE

•

CHANGE KEYS

•

KM / MILES

ECU DIAGNOSIS

In this mode a chart is displayed showing potential

errors in the control unit.

IT IS NECESSARY REFER TO THE ERROR IN-

DICATIONS GIVEN BY AXONE FOR THIS VE-

HICLE.

The instrument panel does not keep all previous errors stored in its memory.

INSTRUMENT PANEL ERRORS

In this mode, a chart is displayed showing potential

errors in the immobilizer and the sensors connec-

ted to it.

Instrument panel errors

In this mode, a chart is displayed showing potential errors in the immobilizer and the sensors connected

to it.

DSB 01

- Immobilizer failure: key code read but not recognised.

DSB 02

- Immobilizer failure: key code not read (key not present or transponder not working)

DSB 03

- Immobilizer failure: aerial not working (open or short-circuited)

DSB 04

- Internal controller failure

DSB 05

- -

DSB 06

- Ambient air temperature sensor

Error cause

Electrical system

SL 750 SHIVER

ELE SYS - 24

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 82 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: