APRILIA SL 750 SHIVER Service Station Manual Download Page 66

Page: 66 / 303

TABLE F - INSTRUMENT PANEL CABLES

1. The two medium clamps shall be positioned

so that they match the corresponding sec-

tions of chassis indicated through two turns

of red belt.

2. Place the clamp as close as possible to the

chassis vertical tube.

TABLE G - AIR TEMPERATURE CONNECTOR

AND FRONT HEADLAMP CABLE

•

Use a small clamp to fasten the air

temperature connector and the front

headlamp cable to the main cable har-

ness.

TABLE H - COIL CABLE

•

Fasten the coil cable with a small

clamp.

TABLE I - HOUSING AND CENTRAL CABLE GUIDE

1. The housing containing light switch and key connectors shall be placed freely over the branch

with the clamp and not fixed.

2. Place medium clamps on the central cable guide that holds only the branch that leads to the filter

casing left side.

Electrical system

SL 750 SHIVER

ELE SYS - 8

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 66 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: