APRILIA SL 750 SHIVER Service Station Manual Download Page 48

Page: 48 / 303

•

Using a thickness gauge, measure the

distance between the tip of the crank-

shaft and the valve bowl.

•

Take note of the measurement.

If valve clearance is not within the tolerance range,

adjust as follows:

•

Take the engine to the TDC.

•

Lock the camshafts by using the cor-

responding timing pins.

Specific tooling

020719Y Timing pin

Characteristic

Valve clearance at intake

0.11 - 0.18 mm (0.0043 - 0.0071 in)

Outlet valve clearance

0.16 - 0.23 mm (0.0063 - 0.0091 in)

•

Remove one camshaft at a time

•

Leave the other camshaft assembled and blocked by means of the timing pin.

CAUTION

IF BOTH CAMSHAFTS ARE REMOVED, THE ENGINE SPINS MAKING TIMING NECESSARY.

•

Remove the bowl tappets and the ad-

justment shims using a magnet.

NOTE

GREASE THE BOWL TAPPETS AND THE AD-
JUSTMENT SHIMS PROPERLY EACH TIME
THEY ARE REMOVED.

•

Replace calibrated pads with a pad

thick enough to correct the valve clear-

ance previously detected.

•

List of calibrated break pads:

1. Calibrated pad 2.60

2. Calibrated pad 2.65

3. Calibrated pad 2.70

4. Calibrated pad 2.75

5. Calibrated pad 2.80

Maintenance

SL 750 SHIVER

MAIN - 12

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 48 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: