APRILIA SL 750 SHIVER Service Station Manual Download Page 3

Page: 3 / 303

SERVICE STATION MANUAL

SL 750 SHIVER

NOTE

Provides key information to make the procedure easier to understand and carry out.

CAUTION

Refers to specific procedures to carry out for preventing damages to the vehicle.

WARNING

Refers to specific procedures to carry out to prevent injuries to the repairer.

Personal safety

Failure to completely observe these instructions will result in serious risk of personal

injury.

Safeguarding the environment

Sections marked with this symbol indicate the correct use of the vehicle

to prevent damaging the environment.

Vehicle intactness

The incomplete or non-observance of these regulations leads to the risk of serious

damage to the vehicle and sometimes even the invalidity of the guarantee.

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 3 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: