manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 296 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 296

•

Disconnect the two connectors.

•

Remove the filter casing together with

the throttle body, by lifting it up from

behind.

CAUTION

COVER THE COUPLING OPENINGS SO THAT
NO FOREIGN BODIES COME IN.

Should the throttle body be removed, disconnect either the map sensor pipes or the inlet ducts; it is

necessary to check the air system tightness. Using Axone, check the following parameters:

a - take the vehicle temperature to 90 °C (194 °F) or above.

b - front cylinder throttle valve correction between - 60 and 60.

b - rear cylinder throttle valve correction between - 60 and 60.

c - potentiometer 1 front throttle valve value is 0.5 or above.

d - potentiometer 1 rear throttle valve value is 0.5 or above.

e - the difference of throttle valve correction values between the front and rear cylinders should not

exceed 0.6.

See also

Air filter

Fuel tank

•

Remove the saddle.

•

Remove the side fairings.

Bodywork

SL 750 SHIVER

BODYW - 10

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments