manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 288 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 288

Seat

SADDLE REMOVAL

•

Place the vehicle on the service stand.

•

Insert the key (1) in the lock.

•

Turn the key (1) anticlockwise

•

Paying attention to the belt position, re-

lease and lift the saddle (2).

SADDLE LOCK

•

Insert the bottom front lugs under the

rear frame pin.

•

Paying attention to the belt position, set

the saddle (2) in its position and push,

until it clicks shut.

CAUTION

BEFORE LOWERING AND LOCKING THE SAD-
DLE, CHECK THAT THE KEY HAS NOT BEEN
LEFT INSIDE THE GLOVE-BOX / TOOLKIT
COMPARTMENT

.

Headlight assy.

•

Remove the instrument panel.

•

Working from the vehicle left side, un-

screw and remove the pin, and collect

the nut and the washer from the right

side.

•

Disconnect the front turn indicator ca-

ble harness.

Bodywork

SL 750 SHIVER

BODYW - 2

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments