manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 282 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 282

•

Unscrew and remove the rotor control

gear fixing nut and act on the gear hex-

agonal insert.

•

Remove the rotor control gear.

•

From the cover inside to the outside,

remove the rotor control shaft with a

punch and a rubber hammer.

REFITTING

•

Upon refitting, carry out the removal operations but in reverse order.

•

From the outside to the inside, fit the

rotor shaft plus the seal in the corre-

sponding hole on the cover.

•

Drive the shaft plus the seal on the

cover using the specific tool and a hy-

draulic press.

•

Refill the expansion tank so that the level is between the MAX and MIN marks.

•

Fill the system through the radiator cap.

Cooling system

SL 750 SHIVER

COOL SYS - 6

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments