manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 271 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 271

Removal

•

Remove the safety circlip.

•

Unscrew and remove the pin.

•

Extract one pad at a time.

CAUTION

AFTER REMOVING THE PADS, DO NOT OP-
ERATE THE BRAKE CONTROL LEVER OR THE
CALLIPER PLUNGERS COULD GO OUT OF
THEIR SEATS RESULTING IN BRAKE FLUID
LEAKS.

Bleeding the braking system

Front

If there is air in the hydraulic system, it acts as a bearing, absorbing a large part of the pressure from

the brake pump and minimising calliper efficiency during braking.

The presence of air is signalled by the "sponginess" of the brake control and poor braking efficiency.

CONSIDERING THE DANGER FOR VEHICLE AND RIDER, IT IS STRICTLY NECESSARY, AFTER
REFITTING BRAKES AND RESTORING THE BREAKING SYSTEM TO THE REGULAR USE CON-
DITIONS, THAT THE HYDRAULIC CIRCUIT BE AIR PURGED.

NOTE

SL 750 SHIVER

Braking system

BRAK SYS - 5

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments