manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 27 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 27

CONNECTING RODS

Specification

Desc./Quantity

Type E1 crankshaft

Original connecting rod type: brown

Spare connecting rod type: brown

Type E2 crankshaft

Original connecting rod type: blue

Spare connecting rod type: blue

Type E3 crankshaft

Original connecting rod type: yellow

Spare connecting rod type: yellow

Type E4 crankshaft

Original connecting rod type: green

Spare connecting rod type: green

Type E5 crankshaft

Original connecting rod type: pink

Spare connecting rod type: pink

Type E6 crankshaft

Original connecting rod type: black

Spare connecting rod type: black

Type E7 crankshaft

Original connecting rod type: white

Spare connecting rod type: white

CAUTION

THE CONNECTING RODS OF THE SAME CRANKSHAFT MUST BE THE SAME COLOUR AND
HAVE THE SAME TYPE OF COUPLING AS THE CRANKSHAFT.
UPON REFITTING, MAKE SURE THAT THE HALF-BUSHINGS ARE OF THE SAME TYPE.

See also

Removing the clutch cover
Removing the flywheel cover

Recommended products chart

R

ECOMMENDED PRODUCTS

Product

Description

Specifications

AGIP RACING 4T, SAE 15W-50

Engine oil

Use top-branded oils that meet or

exceed the requirements of API
SJ/CCMC G4/ACEA A3-04/ JA-

SO MA specifications.

AGIP FORK 5W

Fork oil

SAE 5W

AGIP MP GREASE

Grease for bearings, joints, cou-

plings and levers

Alternatively to the recommen-

ded product, use top-branded

grease for roller bearings, useful

temperature range: -30°C...

+140°C (-22°F...+284°F), drop

point: 150°C...230°C (302°F...

446°F), high anticorrosive pro-

tection, good water and rust re-

sistance.

AGIP CHAIN GREASE SPRAY

Recommended CHAIN oil

Grease

AGIP BRAKE 4 / BRAKE 5.1

Recommended BRAKE FLUID

-

AGIP BRAKE 4 / BRAKE 5.1

Recommended CLUTCH FLUID

-

SPECIAL AGIP PERMANENT

fluid

Recommended ENGINE COOL-

ANT

Biodegradable coolant, ready for

use, with "long life" technology

and characteristics (pink). Freez-
ing protection up to -40°C (-104°

F). According to CUNA 956-16

standard.

SL 750 SHIVER

Characteristics

CHAR - 21

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments