manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 246 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 246

•

Screw the specific perforated rod on

the pumping member threaded rod.

Specific tooling

AP8140150 Perforated rod for pumping mem-
ber air bleed

•

Fit the centring plate.

•

Fit the pumping member together with

the centring plate in the sleeve.

•

Insert the special washer in the screw.

•

Tighten the screw to the prescribed tor-

que.

UPON REFITTING, REPLACE THE SAFETY
WASHER WITH A NEW ONE.

Locking torques (N*m)

Screw fixing the stem in wheel carrier -
M10x1.5 (2) 20 Nm (14.75 lbf ft)

Filling oil

NOTE

THE OPERATIONS DESCRIBED BELOW ARE VALID FOR BOTH STEMS.

•

Place the fork stem on a work table in upright position.

•

Fill the sleeve with the adequate quality and type of oil indicated on the recommended prod-

ucts table.

WARNING

MOVE THE PUMPING ELEMENT SEVERAL
TIMES UNTIL AIR BUBBLES ARE SEEN ON
THE OIL SURFACE.

THE SLEEVE MUST BE PERFECTLY VERTI-
CAL FOR A CORRECT OIL LEVEL MEASURE-
MENT. THE OIL LEVEL MUST BE THE SAME IN
BOTH STEMS.

Characteristic

Fork oil quantity (for each stem):

535 cm³ (32.65 cu.in)

Suspensions

SL 750 SHIVER

SUSP - 16

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments