manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 239 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 239

•

Being careful not to damage the fork

stem when placing it in a vice, in verti-

cal position, using the appropriate pro-

tection.

Specific tooling

AP8140149 Protection for fitting operations

•

Unscrew the sleeve cap.

•

Drain the oil into a container of suitable

capacity to collect fluids.

DO NOT DISPOSE OF OIL INTO THE ENVIRON-
MENT.
DISPOSE OF ENGINE OIL STORED IN A
SEALED CONTAINER AND TAKE IT TO YOUR
SUPPLIER OR TO THE NEAREST USED OIL
RECLAMATION FIRM.

See also

Removing the fork legs

Disassembling the fork

WARNING

DO NOT INTERCHANGE THE STEMS, THEY HAVE INTERNAL DIFFERENCES. THE LEFT CAR-
TRIDGE (2) HAS A SLOT AT THE BOTTOM, WHILE THE RIGHT ONE (1), HAS A SLOT ON THE
UPPER SIDE.

SL 750 SHIVER

Suspensions

SUSP - 9

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments