manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 235 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 235

ALWAYS REPLACE BOTH BEARINGS.
ALWAYS REPLACE THE BEARINGS WITH OTHERS OF THE SAME TYPE.

GASKETS

•

Check that the gaskets are in good conditions; replace them if they show signs of damage

or excessive wear.

ALWAYS REPLACE BOTH GASKETS.
ALWAYS REPLACE THE GASKETS WITH OTHERS OF THE SAME TYPE.

WHEEL PIN

•

Using a dial gauge, check the wheel

pin eccentricity. If the eccentricity ex-

ceeds the limit value, replace the wheel

pin.

Characteristic

Maximum eccentricity:

0.25 mm (0.0098 in)

•

Using a dial gauge, check that the ra-

dial (A) and the axial (B) eccentricities

of the rim do not exceed the limit value.

An excessive eccentricity is usually

caused by worn or damaged bearings.

Replace the rim if, after replacing the

bearings, the value is not within the

specified limit.

Characteristic

Maximum radial and axial eccentricity:

2 mm (0.0079 in)

SL 750 SHIVER

Suspensions

SUSP - 5

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments