APRILIA SL 750 SHIVER Service Station Manual Download Page 234

Page: 234 / 303

•

Tap the wheel pin with a rubber ham-

mer so that the holes on the opposite

side are exposed.

•

Remove the wheel pin by inserting a

screwdriver in the holes on the pin.

•

During extraction, support the wheel and then remove it.

•

Collect the spacer from the front wheel

left side.

Checking the front wheel

FRONT WHEEL BEARINGS

Carry out the check with the bearings fitted on the wheel.

CHECK THAT ALL THE PARTS ARE IN GOOD CONDITIONS, ESPECIALLY THOSE MENTIONED
BELOW.

ROTATION CHECK

•

Manually rotate the inside ring of each bearing. Rotation must be constant, smooth and

noiseless.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

RADIAL AND AXIAL CLEARANCE CHECK

•

Check the radial and axial clearance.

Axial clearance: a minimum axial clearance is allowed.

Radial clearance: none.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

Suspensions

SL 750 SHIVER

SUSP - 4

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 234 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: