manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 23 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 23

Name

Torque in Nm

Screw fixing engine Bracket / clutch side crank-

case half - M6 (2)

12 Nm (8.85 lbf ft)

Crankshaft access cover (1)

4 Nm (2.95 lbf ft)

H20 Pump Rotor (1)

4.50 Nm (3.32 lbf ft)

Screw fixing Stick-coil / Head cover - M6 (2)

5.50 Nm (4.06 lbf ft)

Screw fixing plate / "split" clutch cover - M4 steel

A2 (6)

3 Nm (2.21 lbf ft) (Loctite 243)

THROTTLE BODY / FILTER HOUSING

Name

Torque in Nm

Intake Fitting fixing screw - M6 (8)

12 Nm (8.85 lbf ft) (Loctite 242)

Screw fixing Injection Throttle Body - M6 (8)

12 Nm (8.85 lbf ft) (Loctite 242)

rbw control unit fixing screw - M5 (2)

3.50 Nm (2.58 lbf ft) (Loctite 242)

Injectors fixing screw - M6 (2)

12 Nm (8.85 lbf ft) (Loctite 242)

Crosshead self-tapping screw fixing cover/ filter

casing - M5x20 (8)

3 Nm (2.21 lbf ft)

Crosshead self-tapping screw fixing partition / filter

casing - M5x20 (10)

3 Nm (2.21 lbf ft)

Crosshead self-tapping screw fixing side cover /

filter casing - M5x20 (3)

3 Nm (2.21 lbf ft)

Crosshead self-tapping screw 5x10 (2)

3 Nm (2.21 lbf ft)

Overhaul data

Assembly clearances

Cylinder - piston assy.

The pistons are available in four size types (A, B,

C, D) to be coupled to the four cylinder types (A,

B, C, D).

Only one type of piston ring is available.

SL 750 SHIVER

Characteristics

CHAR - 17

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments