APRILIA SL 750 SHIVER Service Station Manual Download Page 209

Page: 209 / 303

8. Plain washer

9. Nut

10.Roller

11.Bushing

•

Slide off the crankshaft.

See also

Splitting the crankcase halves

Inspecting the crankcase halves

BEARINGS AND OIL SEAL CHECK

Thoroughly clean the two sections of the crankcase, the ball bearings, the threads of the crankcase

fixing screws and the bearing seats with a non-aggressive solvent. Clean the seal surfaces and check

that they are not damaged.

CAUTION

TO AVOID DAMAGING BOTH CRANKCASE HALVES PLACE THEM ON A FLAT SURFACE.

Check that both crankcase halves are not cracked or damaged.

Check that all threads are in proper conditions.

Check that all oil seals remaining in their position are not worn or damaged.

Check all ball bearings for clearance, smoothness and potential distortions.

CAUTION

LUBRICATE BALL BEARINGS WITH ENGINE OIL BEFORE FURTHER CHECKING.

If the internal ring does not rotate smoothly and silently or if there is some noise while it turns, it means

that the bearing is faulty and must be replaced.

OIL FILTER AND OIL DELIVERY PIPE CHECK

Check the oil filter for damage. If necessary, replace the part.

Clean the oil net with petrol and inspect the net links for potential damage.

SL 750 SHIVER

Engine

ENG - 61

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 209 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: