manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 190 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 190

See also

Removing the cylinder head
Removing the cylinder

Checking the cylinder

•

All seal surfaces must be clean and flat.

•

Make sure all threads are in proper conditions.

•

Check cylinder sliding surface for signs of friction and scratches. Also check the seal sur-

faces for damages.

CAUTION

IF THE GROOVES ON THE CYLINDER LINER ARE EVIDENT, REPLACE THE CYLINDER AND
THE PISTON.

•

Clean off lime scales on the cylinder

cooling slots.

•

Measure the cylinder bore at a dis-

tance of 10 - 43 - 90 mm (0.39 - 1.69 -

3.54 in) from the head coupling sur-

face; the highest value should be

considered to estimate wear limits.

Cylinder bore "C": 92.000 mm (3.6220 - in) C=

D1 or D2 max

Cylindricity tolerance: 0.020 mm (0.00079 in)

Replace the cylinder, the piston and the piston ring

all together if not complying with specifications.

Engine

SL 750 SHIVER

ENG - 42

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments