manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 185 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 185

•

Using the specific template, check the

correct position of the cams.

NOTE

USE OF THE TEMPLATE: THIS TOOL IS
PLACED ON THE CAMS WITHOUT THE CAM
CAPS, USING THE PROFILE MARKED WITH
THE NUMBER OF THE CYLINDER BEING
USED, WITH THE MARKINGS FACING THE
FLYWHEEL SIDE.

NOTE

THE TEMPLATE IS NOT A TOOL DESIGNED
FOR TIMING BUT FOR IDENTIFYING THE COR-
RECT DIRECTION FOR CAMSHAFT FITTING
(THE SHAFTS MAY BE FITTED ROTATED BY
180° WITH REFERENCE TO THE CORRECT
POSITION).

Specific tooling

020723Y Template for timing overhead cam-
shafts

•

Place the cam cap.

•

Pre-tighten the eight screws in the se-

quence indicated, to the prescribed tor-

que.

•

Tighten the eight screws in the se-

quence indicated, to the prescribed tor-

que.

•

Carry out camshaft timing with the ap-

propriate dowels.

Specific tooling

020719Y Timing pin

Locking torques (N*m)

Cam cap/head fixing screws - M6 (16) Pre-tight-
ening: (4.90 - 6.86) Nm ((3.61 - 5.06) lbf ft) Tight-
ening: (9.81 - 12.75) Nm ((7.24 - 9.40) lbf ft)

CAUTION

INSTALL THE CAMSHAFT TIGHTENING NUTS WITH THE MARK FACING UP.

•

Pre-tighten the gear nut on the camshaft.

REFIT THE NUT WITH THE MACHINED SURFACE FACING THE GEAR (THE MATERIAL ACRO-
NYM SHOULD BE VISIBLE).

Locking torques (N*m)

Nut fixing camshaft gears (pre-tightening) - M15x1 (4) 30 Nm (22.13 lbf ft)

SL 750 SHIVER

Engine

ENG - 37

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments