manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 174 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 174

9. Stud bolt

10.Water pipe fitting

11.TBEI screw

12.Joint

13.O-ring

14.Flanged nut M8X1.25

15.Flanged nut

16.Valve sealing ring

17.TE flanged screw

18.Lock nut M10x1.25

19.Water Temperature Sensor

20.Threaded cap M6X10

21.Threaded cap

22.TE flanged screw

23.To radiator

Removing the overhead camshaft

•

Remove the clutch side crankcase

half.

•

Rotate the crankshaft until the rear cyl-

inder reaches the TDC.

First remove the rear head cover in order to re-

move the rear head camshafts.

First remove the front head cover in order to re-

move the front head camshafts.

Mark the head camshafts, the corresponding

sprocket wheels and cam caps in order not to in-

terchange them upon refitting.

•

Undo and remove the eight cam cap

screws working in a diagonal se-

quence and in stages.

Engine

SL 750 SHIVER

ENG - 26

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments