manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 166 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 166

•

Collect the spacer and the needle

bearings.

•

Collect the shim washer.

Checking the clutch plates

•

Lay the friction discs and steel discs on

a level surface and check them for

cracks and potential distortions.

Maximum distortion allowed: 0.20 mm (0.0079

in)

•

Measure the driving plate thickness at

four positions, replace them all if not

complying with specifications.

CAUTION

THE STEEL DISCS MUST SHOW NO SCORES
OR TEMPERING COLOUR.

•

Measure the thickness of the clutch

discs at four positions, replace them if

not complying with specifications.

Thickness of nine drive discs: 2.5 mm (0.10 in).

Driven disc thickness: 2.95 ÷ 3.05 mm (0.116 ÷

0.120 in)

Engine

SL 750 SHIVER

ENG - 18

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments