manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 162 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 162

Removing the clutch cover

•

Undo and remove the side fixing

screws.

•

Remove the clutch cover.

It is advisable to remove only the clutch cover in

order to replace the clutch discs. Should the com-

plete clutch assembly be removed, remove the

crankcase, clutch side.

It is however possible to remove the complete

clutch assembly by removing only the clutch cover.

In this case carry out the following operations:

•

measure the clutch bell protrusion from

the crankcase before removal;

•

during refitting, first check that the

measurement has not changed, then

tighten the clutch nut. If it has changed,

rotate the crankshaft so that the oil

pump control drive gear engages cor-

rectly with the oil pump driven gear on

the clutch bell.

Engine

SL 750 SHIVER

ENG - 14

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments