manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 147 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 147

•

Working on the right side, insert the

three bolts with their washers.

•

Working on the right side, place the

spacers on the three bolts between the

engine block and the chassis.

CAUTION

THE SPACERS HAVE DIFFERENT SIZES. RE-
FIT THEM IN THE SAME WAY THEY WERE
BEFORE BEING REMOVED.

•

Working from the left side, tighten the

three nuts.

•

Release the engine from the belt and

the hoist.

•

Refit the pinion and restore the gearing

chain clearance.

•

Reconnect the electric connections

and clamp the cable harnesses.

•

Carry out the vehicle preparation oper-

ations but in reverse order, restore the

correct level of all fluids and carry out

the adjustments that may be required.

See also

Vehicle preparation
Adjusting

SL 750 SHIVER

Engine from vehicle

ENG VE - 7

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments