APRILIA SL 750 SHIVER Service Station Manual Download Page 132

Page: 132 / 303

•

If shorted to positive: excessive voltage has been detected at PIN 54 of the VEHICLE con-

nector.

•

If shorted to negative: short circuit to ground detected.

•

If the circuit is open: interrupted circuit detected. Excessive voltage can only be detected

after the fan relay gets activated.

Troubleshooting

•

If shorted to positive: check the relay electrical specifications are correct by disconnecting

it from the cable harness. If they are not correct, replace the relay; if correct, restore the

cable harness (pink/blue cable).

•

If shorted to negative: check the relay electrical specifications are correct by disconnecting

it from the cable harness. If they are not correct, replace the relay; if correct, restore the

cable harness (pink/blue cable).

•

If the circuit is open: check the relay connector and the Marelli control unit VEHICLE con-

nector: If not OK, restore; if OK, restore the cable harness (red/blue cable).

RUN/STOP switch

Run / stop switch

Function

It tells the control unit if the driver wishes to enable

engine start-up or to keep the engine running.

Operation / Operating principle

If the driver wants to shut off the engine or to dis-

able engine start-up, the switch should be open,

i.e. the Marelli control unit should not detect volt-

age at VEHICLE connector PIN 2.

Level in wiring diagram:

Start-up enabling

switches.

Location:

Electrical system

SL 750 SHIVER

ELE SYS - 74

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 132 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: