APRILIA SL 750 SHIVER Service Station Manual Download Page 125

Page: 125 / 303

Error DSB 08

Error cause

•

An oil sensor failure is signalled when,

with engine running, it is detected that

the sensor circuit is closed. This error

is signalled by the bulb icon and the

general warning light turns on as well.

Troubleshooting

•

Check if oil pressure is low with the

specific gauge.

Neutral sensor

GEAR IN NEUTRAL SENSOR

Function

it tells the gear position to the control unit: in neu-

tral or in gear.

Operation / Operating principle

for gear in neutral, the circuit is closed to ground

connection: then, via CAN, the control unit sends

the signal to the instrument panel which turns on

the neutral speed warning light.

Level in wiring diagram:

start-up enabling

switches

Location:

•

on the vehicle: left side of the vehicle,

near flywheel cover

•

connector: upper part of the flywheel

cover

Electrical characteristics:

•

gear in neutral: closed circuit (continu-

ity)

•

gear engaged: open circuit (infinite re-

sistance)

Pin-out:

1. Voltage 12V

CAUTION

SL 750 SHIVER

Electrical system

ELE SYS - 67

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Search results

Summary of Contents for SL 750 SHIVER

Reviews:

APRILIA SL 750 SHIVER, Service Station Manual, Page: 125 / 303

Search results

Summary of Contents for SL 750 SHIVER

Reviews: