manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 124 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 124

Engine oil pressure sensor

ENGINE OIL PRESSURE SENSOR

Function: it i

ndicates to the instrument panel if

there is enough oil pressure (0.5 +/- 0.2 bar (7.25

+/- 2.9 PSI)) in the engine.

Operation / Operating principle:

 normally closed

switch. With oil pressure above 0.5 +/-0.2 bar (7.25

+/- 2.9 PSI), open circuit.

Location on the vehicle

: right side of the vehicle,

under the oil sump

Pin-out

: Voltage 5V

Instrument panel

Error DSB 07

Error cause

•

An oil sensor failure is signalled when,

with engine off, it is detected that the

sensor circuit is open. The test is per-

formed only once when the key is set

to ON. This error is signalled by the

bulb icon and the general warning light

turns on as well.

Troubleshooting

•

Check the sensor connector and the

instrument panel connector (PIN 17): If

not OK, restore. If OK, check the con-

tinuity of the purple cable between the

sensor connector and the instrument

panel connector PIN 17: if not OK, re-

store the cable harness; if OK, replace

the sensor.

Electrical system

SL 750 SHIVER

ELE SYS - 66

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments