manualshive.com logo in svg

APRILIA SL 750 SHIVER, Service Station Manual, Page: 105 / 303

Share
Download
APRILIA SL 750 SHIVER Service Station Manual Download Page 105

•

on the vehicle: on filter casing

•

on connector sensor: near the probes

Electrical characteristics:

•

Resistance at 0°: 32.5 k

ȍ

 +/- 5%

•

Resistance at 25°: 10.0 k

ȍ

 +/- 5%

Pin-out:

1. 0-5 V signal: PIN 1

2. Ground connection: PIN 2

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL CON-
CEPTS OF ELECTRICAL TROUBLESHOOTING FOUND AT THE BEGINNING OF THE CHECKS
AND CONTROLS SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: PARAMETERS

Air temperature

Example value:

 26° C

In case of recovery, this value is set by the control unit.

Air Temp. before Recovery

Example value:

 -40° C

Value drawn from the signal read without taking into account any recovery: the value in the example

refers to an open circuit.

AXONE: ELECTRICAL ERRORS

air temperature sensor P0110

 - open circuit, shorted to positive / shorted to negative.

Error cause

•

If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 63 of

the ENGINE connector. If shorted to negative: voltage equal to zero has been detected at

PIN 63 of the ENGINE connector.

Troubleshooting

•

If the circuit is open, shorted to positive: check the sensor connector and the Marelli control

unit connector. If they are OK, check sensor continuity: replace the sensor if not OK; if it is

OK, check continuity between the ENGINE connector PIN 63 and the sensor PIN 1: restore

cable harness if there is not continuity; if it is OK, reconnect the control unit connector and,

with key set to key ON, check the continuity between the sensor connector PIN 2 and the

vehicle ground connection: if it is OK, it means that the error cause is that the cable is short

circuit to positive and it is necessary to restore the cable harness between the ENGINE PIN

63 and the sensor PIN 1; check the sensor connector and the Marelli control unit connector.

If not OK, restore the cable harness. If OK, check continuity between the ENGINE connector

PIN 35 and the sensor connector PIN 2: restore the cable harness if there is not continuity.

SL 750 SHIVER

Electrical system

ELE SYS - 47

Summary of Contents for SL 750 SHIVER
















































































































































































































































































































Reviews:

No comments